Dealer portal
Accessories and spare part
ERATAC shot angle compensator
When firing accurately at long range, at very high or very low targets, a changed point of impact must be taken into account due to the deviating bullet trajectory. Shot angle compensators (SWK) make it possible to calculate the trajectory compensation to be set. ...
Further information
item no.: 018177
ERATAC ring mounting 30mm, BH 13mm
Made of high-strength aluminum and hard-anodized according to Mil-Spec.
Type III matt black. They are available in a version with hexagon nuts. Each 25 mm wide ring is equipped with our UNIVERSAL interface.
interface. Available with rings in diameter
30 mm and 34 mm in various heights.
Further information
item no.: 018176
ERATAC ring mounting D 34mm, BH 13mm
Made of high-strength aluminum and hard-anodized according to Mil-Spec. Type III matt black. They are available in a quick-release version with hexagonal nuts. Each 25 mm wide ring is equipped with our UNIVERSAL interface. Available with 30 mm and 34 mm diameter rings in various...
Further information
item no.: 016470
ERATAC block mount 30mm, BH 20mm, 0-70 MOA
Adjustable from 0 - 70 MOA in steps of 10 MOA each. It is not
necessary to remove telescopic sight and mount. Adjustment on the
on the weapon possible. 100% repeat accuracy and shooting stability.
Further information
item no.: 018174
ERATAC mount with level for Picatinny rail
You can use the bubble level to correct your position and thus avoid tilting.
Further information
item no.: 018179
Picatinny rail for 1761 - MOA 0, aluminum
With integrated abutment for maximum stability during mounting. Mounting screws with brass insert prevents scratching and damage to the rifle case. For 11 mm prism rail. Suitable for right and left hand versions.
Further information
Item no.: 015018
Picatinny rail for 1727 - MOA 30, aluminum
For mounting optical sights. Suitable for all models of the 1727 F series. With 30 MOA forward tilt.
Further information
item no.: 018758
Picatinny rail for 1761 - MOA 30, aluminum
With integrated abutment for maximum stability during mounting. Mounting screws with brass insert prevents scratching and damage to the rifle case. For 11 mm prism rail. Suitable for right and left hand versions. With 30 MOA pre-tilt.
Further information
item no.: 016989
Picatinny rail for 1710 and 1712 - MOA 0, aluminum
For mounting optical aiming devices. Suitable for all models of the 1710/1712 series.
Further information
Item no.: 014736
Picatinny rail MDT for 1710 and 1712 - MOA 20
For mounting optical sights. Suitable for all models of the 1710/1712 series. 20 MOA forward tilt.
Further information
item no.: 018036
Picatinny rail for 1710 and 1712 - MOA 30, aluminum
For mounting optical sights. Suitable for all models of the 1710/1712 series. 30 MOA forward tilt.
Further information
item no.: 018757
ERATAC holder with bubble level for universal interface
Suitable for the interface adapters of ERATAC riflescope mounts. The level can be mounted on either the left or right side. This enables precise
alignment of the rifle, a correction of the stop and thus prevents the rifle from tilting.
Further information
item no.: 018178
ERATAC block mounts 2" extended, 30mm, BH 22mm, 20 MOA
95 mm long contact surface for a tight and backlash-free fit on the
Picatinny rail. Available with ring diameters of 30 and 34 mm
in 2 different heights, with or without 20 MOA pre-tilt. lock up via hexagon nut (T5 series).
Further information
item no.: 018175