FAQs

How do I clean my rifle?

In order to ensure consistent accuracy in the long term, it is essential to clean the rifle regularly after shooting. The cleaning intervals and the cleaning intensity depend in particular on the number of shots fired, the caliber, the ammunition used and the individual development of the shot pattern of the individual rifle. The accessories market now offers a [...]

How do I clean my rifle? Read more "

Which compressed air cylinders may be used on ANSCHÜTZ compressed air rifles?

Please only use original ANSCHÜTZ compressedcompressed air cylinders and always observe the operating instructions! ANSCHÜTZ accepts no liability for damage of any kind caused by alteration of parts, conversion or installation of non-original ANSCHÜTZ parts or failure to observe the operating instructions. ATTENTION: The use of non-original ANSCHÜTZ compressedcompressed air cylinders will damage your air rifle and invalidate your liability and warranty.

Which compressed air cylinders may be used on ANSCHÜTZ compressed air rifles? Read more "

Will a Match54 KK-BarreledBarreled action or a 1413 Match-KK-BarreledBarreled action fit into a 1918 Precise aluminum stock?

The answer can generally be affirmative, but the following points must be considered in advance: Adjustments may have to be made to the stock in the area of the safety by a gunsmith . It should also be noted that the sash lock on the match lock is no longer functional, as the sash lock can no longer be set to "safe" mode. The trigger 5018

Will a Match54 KK-BarreledBarreled action or a 1413 Match-KK-BarreledBarreled action fit into a 1918 Precise aluminum stock? Read more "

Are there threaded screws to close the threaded holes in the ANSCHÜTZ locking sleeves?

The set screw 1403-005, part number: 002864, is available for closing the threaded holes on the locking sleeves (housing) of the barreled actions 1780, 1770, Match54 and Match64 models. It is recommended to to set the safety screws with Loctite (screw locking) to set the safety. 5 set screws 1403-005 are required for Barreled action 1780 5 set screws 1403-005 are required for Barreled action 1770 5 set screws 1403-005 are required for Barreled action Match54

Are there threaded screws to close the threaded holes in the ANSCHÜTZ locking sleeves? Read more "

What is the difference between the 7002 and 6805 diopters?

Both rear sights, the 7002 as well as the 6805, are suitable for all ANSCHÜTZ match rifles.difference:On the rear sights 6805 the elevation adjustment slides in an adjustable V-block, the windage on a dowel pin. On the rear sights 7002, the elevation and windage run on ground ball bearings. This model also offers the option of tilt compensation. Both rear sights operate backlash-free.

What is the difference between the 7002 and 6805 diopters? Read more "

What does "laser class 1" mean for the LaserPower / laser beam rifle?

Laserklasse 1: Die zugängliche Laserstrahlung ist unter vernünftigerweise vorhersehbaren Bedingungen ungefährlich. Laser mit sehr geringer Leistung (<= 1mW). Diese Laser verursachen auch bei längerer Bestrahlung keine Schäden am Auge, selbst dann nicht, wenn optische Instrumente (Lupen, Linsen, Teleskope) in den Strahlengang gehalten werden.

What does "laser class 1" mean for the LaserPower / laser beam rifle? Read more "

What is the warranty claim when using non-original ANSCHÜTZ compressed air cylinders?

Please only use original ANSCHÜTZ compressedcompressed air cylinders and always observe the operating instructions! ANSCHÜTZ accepts no liability for damage of any kind caused by alteration of parts, conversion or installation of non-original ANSCHÜTZ parts or failure to observe the operating instructions. ATTENTION: The use of non-original ANSCHÜTZ compressedcompressed air cylinders will damage your air rifle and invalidate the warranty. Further

What is the warranty claim when using non-original ANSCHÜTZ compressed air cylinders? Read more "

Scroll up